Товары‪» Запасные части и принадлежности‪» Подшипники‪»

Avid 5x16x5 Ceramic Metal

Avid 5x16x5 Ceramic Metal


Цена
7,50 + расходы на доставку
Цена с НДС 25.5 %


Количество
шт



В наличии на складе
Store Vaasa0 штк, Только самовывоз.
Store Vantaa2 штк немедленно
При доставке из интернета2 штк немедленно

Код заказа
625ZZC
Штрихкод
818021013929
Наличие
Немедленно

Информация о наличии на складе

Местоположение Store Vantaa: a-110-0000-a-000


Оценки
Общий рейтинг ()


Описание товара

Product Overview

The Avid 5x16x5 Ceramic Metal Bearing (625ZZC) is replacing our motor line because it was overkill and we feel it was a waste of money that you could spend on other things. The bearing is a high quality steel/chrome bearing with metal shields and silicone nitride ceramic balls (Si3N4).

A ceramic motor bearing will allow the motor to work more efficiently over a steel bearing allowing for better run times and acceleration. Another benefit to ceramics is the weight difference in the balls allowing for less rotating mass.

If your motor is not listed below, please check with your manufacturer first to see what size you require.

Motors Used In
Tekin: T8 (All) (Takes one 5x11x5 and one 5x16x5)
Feigao: 540 (All) (Takes two 5x11x5)
Tips
Installation: These bearings are made with a very tight tolerance so it is common for the bearing not to slip right on due to the edges on the armature being scarred from a pinion. You may have to lightly sand the armature shaft to get the edges off while adding a drop of oil on it to put the bearing all the way on.
Tekin Shimming: Once it is time to replace your motor bearing most likely the bearing has gotten loose from the aluminum plate allowing for easy replacement. It isn't required but if you know how to shim a motor you may do so with our clutch shims because now the bearing will float a little in the plate. A quick shimming tip is to place a 5mm shim on the shaft before putting the bearing on, then secure the plate to the can with a few screws, now spin the armature so the rotor aligns itself in the can, and pull the rotor towards the bearing you just installed and you should have at least 0.5mm of play. If you have more then you may add another shim
Lubrication: For proper lubrication, you should reoil the bearing with our bearing oil or grease every 20-30 runs to get the most life out of your Avid race bearings.
Break In: For the first run of these bearings, Avid suggests that you run the motor off the ground at 1/4 throttle for 5 minutes so the ceramic balls will seat instead of skidding them.



Bearing Dimensions

METRIC: 5mm (Inner) x 16mm (Outer) x 5mm (Width)
STANDARD: 0.19685" (Inner) x 0.62992" (Outer) x 0.19685" (Width)


Товар может быть доставлен в письме. В письмо поместится 391 штк изделия.

Размер товара в упаковке или размер торговой упаковки составляет 18 x 18 x 18 mm.


1. Inner diameter
5mm


2. Outer diameter
16mm


3. Thickness
5mm


Вес
0,004 kg(Возможно включает вес торговой упаковки)


Страна-производитель
Китай


Комментарии
Добавить комментарий

Марка

Avid
Avid
100 товаров

Товары, которые часто покупают вместе с данным товаром: