Absima AT3.4BL 1:10 Truggy 4WD Brushless RTR:
UNBELIEVABLE POWER - the new Hotshot 3.4BL series is equipped with a powerful brushless electric motor and waterproof electronic speed controller (ESC). Shaft driven 4WD provides you with the necessary traction to maneuver the toughest obstacles and the forward/reverse ESC is beneficial in navigating tight spots. Lightweight plastic chassis, four oil filled adjustable coil over shocks, and independent suspension offer solid performance. Fear not! A 2.4GHz radio system and waterproof electronics ensure control, for those who dare to unleash the power.
HIGHLIGHTS:
Water-resistant 50A BL Speed Controler (programmable)
Powerfull 3300KV BL Motor
2.4GHz A.F.H.D.S. Radio System
Full Aluminum Shocks
Steel Motor Transmission
GENERAL CHASSIS FEATURES:
4WD
Complete ball bearing
Adjustable aluminum oil shocks
Gear differential front/rear
Aluminum motor mount
Complete covered transmission
New chassis layout for better performance
Adjustable turnbuckles
Adjustable wishbones
Aero disc racing wheels
Full printed body
Sticker sheet for a unique design
A lot tune-up parts available!
TECHNICAL SPECIFICATION:
Measure (L/W/H): 405x325x165 mm
Weight: 1550g
Wheelbase: 270 mm
Chassis clearance: 40 mm
Tire width: 55 mm front / 55 mm rear
Tire Ø ± 105 mm
Shock spring force: medium / Length: 85mm f/r
Differential oil viscosity: 1.000 front / 3.000 rear
Shock oil viscosity: 400 f/r
Steel Motor transmission: Pinion 23T / Gear 64T
Pinion module: 0.6
MORE FEATURES:
BL Speed Controller (2110007): programmable (brake power, neutral brake, drive mode, punch, V cut-off) / NiMH (7.2V) & LiPo (7.4V/2S) suitable / Amps: 50A cont./300A peak / BEC 6V/3A / Overheat cut-off / Drive function: front/reverse/brake (standard) / Plug system: T-plug (Deans style)
Servo (2030003): 4kg steering force / 25T outdrive
Motor (2130005): 3300KV / 27.400RPM @ 7.4V / Operating voltage: 4.8 - 11.1V / Size: 540
Radio (2000001): 2-channel radio / 3-channel receiver / reverse / dual rate / trimming
SCOPE OF DELIVERY:
Truggy "AT3.4BL" RTR - brushless version
2.4GHz Radio System
Manual
Sticker Sheet
REQUIRED ACCESSORIES:
Battery - Racing Pack NiMH or LiPo (recommended)
Charger
Absima USB cable charger - NiMH 2A/10W.:
USB-A charging cable with Tamiya plug suitable for NiMH batteries with a capacity of 2000mAh to 5100mAh.
Technical data:
USB-A charging cable Input:100-240V
Max. Output Power: 10W / 2A
Battery type: NiMH 5 - 8 cells
Battery capacity: 2000mAh - 5100mAh
Protection mode: Overvoltage; Short circuit; Reverse polarity
Automatic time-out function: Yes (5.5 hours)
Plug: Tamiya
Cable length: approx. 50cm
Dimensions (L/W/H): 70x25x15 mm
Weight: 22 g
The USB charging cable has an LED indicator. During the charging process, the green LED flashes and the red LED lights up constantly. When the battery is fully charged, the green LED lights up continuously and the red LED is off. If only the red LED lights up continuously, there is a fault or a protective function of the charging cable is active.
Scope of delivery:
1* USB-A charging cable for NiMH batteries (without power supply)
Please note:
The charging speed may vary depending on the power supply unit. To be able to use the full power of the USB charging cable, you need a power supply unit with at least 10W power (output voltage 2A/5V) which supports fast charging. If you use a power supply unit with less power, the charging time will be extended accordingly.
