SaatavuusArviolta
3 - 15 vrk tilauksesta. Jos tuote on loppu toimittajalta toimitusaika voi olla pidempi. Tarkemman toimitusajan voit varmistaa asiakaspalvelustamme. Normaalisti arvion luotettavuus on hyvä.
Varastotilanne ja saapuvatHaluan ilmoituksen, kun tuotetta tulee lisää varastoon
Tuotteen kuvausHobbywing QuicRun WP 16BL30 SL 1/16-1/18 ESC & 2435SL 4500KV G3 Combo - 2-3S LiPo
Easy Operation
This ESC is specially designed for new beginners and intermediate modelers; it not only carries forward the outstanding quality of HOBBYWING products but simplifies the operation.
Applicable to All Weather Conditions
The waterproof and dust-proof design allows the QUICRUN WP-16BL30 to be used in all weather conditions without any issue of damage caused to the ESC from water or dust.
High Reliability & Durability
Reliable hardware combined with advanced software technology allows the QUICRUN WP- 16BL30 to not only provide high power output but also overload protection of the ESC circuit.
Single-button Programming & Factory Reset
The SET button on the ESC allows the user to easily program or factory reset the ESC with ease.
Wide Application
This ESC is applicable to all-weather sport of 1/18th, 1/16th scale touring cars, buggies, trucks, and monster trucks.
ESC Specs:
Type: 1/16, 1/18, Brushless, Sensorless, WP
Cont./Peak Current: 30A/180A
Input: 2-3S LiPo/6-9 Cells NiMH
BEC: Linear Mode: 6V/1A
Input Wires: 16AWG-75mm
Output Wires: 16AWG-75mm
Input Connectors: Small-sized TAMIYA Connector (Mini Tamiya)
Output Connecotors: 3.5 Gold Connector (Female)
(Note: All the wire length above is the original length not the length you see from the outside.)
Programming:
SET Button on ESC: Supported
LED Program Box; Supported
LCD Program Box: Not Supported
WiFi Module: Not Supported
OTA Programmer: Not Supported
Program Port: Program/Throttle Wire
Firmware Upgrade: Not Supported
Size & Weight:
Size: 36x28x18mm
Weight: 38g
Applications:
Motors: Sensorless Brushless
Vehicles: 1/16 & 1/18 - Touring Cars/Buggies/Trucks/Monster Trucks
Motor Limit:
For 2S Lipo or 6 cells NiMH:
On-road: 2435-size or smaller motor with the KV<8000
Off-road / Buggy / Monster: 2435-size or smaller motor with the KV<5000
For 3S Lipo or 9 cells NiMH:
On-road: 2435-size or smaller motor with the KV<5500
Off-road / Buggy / Monster: 2435-size or smaller motor with the KV<3500
Stronger power - Upgraded to 4-pole rotor
The G3 motor adopts a four-pole rotor design with stronger torque and stronger explosive power.
Better performance
Compared with the same specification of products under the same load conditions, the maximum output power is 60% higher, the maximum efficiency is 5% higher, and the temperature is reduced by approximately 30 degrees.
Upgraded materials, durable
0.2mm thick silicon steel, high-strength explosion-proof rotor, 200°C high-temperature-resistant enameled wire, and first-line brand high-precision and high-quality bearings make the motor durable.
Excellent protection
The output of the motor is sealed with a silicone rubber on the housing. It is dust-proof for off-road vehicles/trucks. Users will now enjoy bashing without having to worry in harsh operating environments such as outdoor sand, stones, and dust.
Note: It is recommended to block the unused mounting holes of the motor front cover with screws.
Motor Specs:
Type: 1/18-1/16, Brushless, Sensorless Motor
Poles: 4
KV Rating: 4500
LiPo Cells: 2-3S
No-load Current: 2.1A
O.D.: 24mm
Length: 36mm
Shaft Diameter: 2mm
Connectors: 3.5mm (male)
Weight: 61.2g
Front Bearing: OD8xID3xT4mm
Rear Bearing: OD8xID3xT4mm
Applications: 1/16-1/18 On-road & Off-road
KommentitLisää kommentti
Tuotemerkki